BBSNOTES.txt 6.0 SUGGESTIONS FOR USING PBBS's and for INCLUDING APRS PROTOCOLS IN BBS and NODE SOFTWARE One thing we have learned in maintaining an operational APRS net on 145.79, is that it is very useful for all stations to include in the comment field of their position report the address of their home BBS! Then any station on the APRS frequency immediately learns how to send that station a lengthy packet message. If your TNC supports an internal BBS, it is also useful to leave it on and include its unique address or SSID in your comment field so that stations can access your PBBS even while you are running APRS! A few stations sending keyboard messages into a PBBS on the APRS frequency is not objectionable since the number of packets are small and at typing speed. Also, by having personal mail boxes, users then DO NOT read their mail over the air! I encourage all stations to operate their own PBBS maildrops on the APRS frequency; but please do not use the PBBS's to post messages for others who must read the message over the air. All stations should avoid any other general computer to computer exchanges which would block the frequency for large blocks of time. The remainder of this file is intended for BBS SYSOPS and the writers of BBS and NODE software. Please consider the following advantages to including APRS protocols in your station operation. Since APRS allows stations to see the network topology in real-time, it is ideal for determining the locations of all neighboring BBS's and NODES. If BBS's and NODES simply included either the LAT/LONG or GridSquare in a periodic UI frame, all users could see where the system is located. For permanent sites such as BBS's and NODES, this beacon could probably be transmitted once every hour or so. This !LAT/LONG format can be placed anywhere in the BText to accommodate THENET Nodes and some BBS software where the beginning of the BText is pre-loaded with something already and the !LAT/LONG can only be appended to the end. The exact format of the UI frame should be as follows: BBSXX>APRS:!DDMM.xxN/DDDMM.xxW[comments as desired to end of line [this left bracket is the APRS symbol for BBS BBSXX>APRS:[GRidsq]Comments to end of line For BBS code writers, this process can be enhanced by making the BBS respond to APRS Query packets. One of these packets is transmitted whenever an APRS station initializes his program. On receipt of an APRS Query packet, all stations on frequency set a two minute random timer and respond sometime in the next 2 minutes with their location. This way, any APRS station can obtain the location of all stations on the frequency soon after comming on frequency. The format of the APRS Query packet is W4XYZ>APRS:?APRS?. By including the code in NODE and BBS software to respond to APRS Querys, the periodicity of the APRS position beacon can easily be set quite infrequently since stations can request the BBS position at any time. For those concerned with physical security, the grid square position report can be used which is ambiguous to 3 miles or so instead of the LAT/LONG posit accurrate to 60 feet. MAIL-FOR BEACONS: Since APRS contains a BEACON parser to capture all BEACONS heard on frequency, this is an excellent way for stations to capture MAIL-FOR beacons from BBS's. APRS stations simply call up their LATEST BEACONS display and see if there is any mail for them. For this to work, APRS must see the MAIL-FOR information on the same line as the packet header. MAIL-FOR which is listed on a second line after the header do not show up in the APRS system. For this reason I would like to request BBS SYSOPS to modify their MAIL-FOR beacons to keep the beginning of the MAIL-FOR list on the same line as the packet header. By allowing APRS stations to see mail lists without even logging on, you are helping reduce congestion on the channel. Presently, most stations do not see MAIL-FOR beacons because they scroll off the screen too rapidly. APRS grabs all packets that are TO the following addresses: APRS, BEACON, ID, MAIL, SKYWRN, CQ, GPS, SPCL, and QST. APRS retains the last of these heard per station. APRS can also be told to monitor all OTHER packets with the CONTROLS-OTHER command. Please play with the APRS software and load some of the backup and demonstration files included. I'm sure you will find APRS to be an exciting new capability for packet radio which can make packet radio much more responsive in real-time communications. BBS POSITION DATABASES: Finally, ambitious code writers could add code in their BBS's to capture all APRS position reports heard on frequency. These reports could be retained in a file and be made available to local users. One of these files, if downloaded, can be loaded by APRS users to display the locations of all stations ever heard on the frequency! Talk about good preparations for emergency comms! BBS FORWARDED POSITION REPORTS: Since we already have a worldwide packet network of BBS's which have the ability to forward a packet message anywhere in the country, I would like to see a standard message format built which would permit a mobile, roving packet station to report his location back to his home BBS on a once-a-day type basis. Imagine that this mobile station simply posts a message on any nearby BBS which contains his position and the routing for his home BBS. That packet message would be forwarded via the normal BBS network and arrive at the intended destination whereupon the destination BBS would in turn send out a decaying APRS POSITION beacon reporting that unit's position even if he was thousands of miles away and on the road! All of his buddies (or his wife) would see on their home computers his latest position auto- matically which was actually relayed through the packet BBS network. As with any APRS position report, the beacon periodicity would decay from 10 minutes to once every few hours as the position report got older. The format for such a position report for WB4APR might be as follows: Send: SP APRS @ W3IWI.MD.USA Send command with Routing Subj: !3858.11N/07629.11W/040/010 LAT/LONG/CSE/SPD Msg: Be home at 1200 Saturday. Comment field up to 40 chars /EX On receipt of such a message, the receiving BBS (W3IWI) would form an APRS station reporting UI frame and transmit it periodically as follows: W3IWI>APRS:WB4APR @051937/3858.11N/07629.11W/040/010/Be home at 1200 Saturday As with all APRS packets, this packet would be transmitted once, then one minute later, then 2 minutes later, then 4 minutes later and so on. This doubling ot the packet period after each transmission decays very repaidly to only 4 packets in the first 10 minutes, 3 more in the next hour and only 3 more in an entire 24 hours! This is not such a load! This would only be 8 packets in the first day and only 1 in the second! When the period is greater than 24 hours, the message is deleted from the system. People on the road reporting home would probably send a new message every 24 hours anyway. BBS POSITION DATABASE: Since APRS includes an individual station query capability, a BBS that has accumulated the position of all of its users, could respond to such an APRS query with a one time position report for that station without even logging on. The APRS query is simply a one line APRS message from the querying station to the Queried station with the letters "?APRS" in the first 5 character positions. A BBS with a callsign data base seeing such a packet could respond immediately with a position report for that station! The APRS station would see the position on his map!